F-16 Fighting Falcon Plans

(3 customer reviews)

$ 4.70

F-16 Plans

Categories: ,

Description

Can be powered by up to 70mm EDF or a single pusher motor.  This Mk.4 version of the plans allows scope for a 3d printed intake duct and thrust tube / nozzle for 64mm EDF.

This is for plans only.  Once purchased you will receive a download link to a zipped file.  the PDF files will be within it.

^ See the Build guide in the Tabs above ^

WIKI

https://en.wikipedia.org/wiki/General_Dynamics_F-16_Fighting_Falcon

Build Guide

F-16 construction guide_2019-02-10

Power options

NOTE : These links will open in another tab.

Single Pusher (3s)

50mm EDF (4s)

64mm EDF (3s)

64mm EDF (4s)

70mm EDF (4s)

Videos

Specs

F-16C_FightingFalcon_GA_2017-11-22

Build log

Build log

 

3 reviews for F-16 Fighting Falcon Plans

  1. Κostantinos

    Hey Guys!! WHAT AN AWESOME PLANE!! you should definitely buy and build this one! this is just SPECTACULAR! i have build my own with CFT tanks on the main fuselage and it flies with out problemAsk Craig for help if you think that this is necessary but for sure this plane is JUST AMAZING!! Check out my Maiden Flight here!! https://www.youtube.com/watch?v=FbYdr5bZpHk&feature=youtu.be&fbclid=IwAR3xA1UlD8gI3LfFafapn4sFFebQM32ToWq7pZCV3fIU_-BuaSVZsZ5keZg You should go for it guys 😉 support Craig for this unique work!!

  2. Olaf Haack

    Here is a short summary of building and flying this awesome F-16 Jet in 115% size.
    I decided to build it in a two seater variant and in newer Block 50 livery with a different turtle deck design, painted in IAF Paint scheme. Building her up is quite easy, in 115% size you can still use 6mm Depron sheets without problems. Using a 70mm EDF/4S setup is recommended (or similar pusher setup). I used all new 3D printed parts too. For having a perfect fit of the doubleseater canopy, you have to modify the fuselage with an additional depron layer near the canopy area. Reinforce the rear section of the fuselage sides where you find the bearings of the elevator tubes is also recommended. Use 4 mm liteply.
    CG shown on the general arrangement overview is spot on. Dont forget to recalculate when going with other scale than 100%. Elevator is in 3-4 mm up position (front tip down!) when Tx Sticks are neutral, this provides a straight flight without dive tendencies. Flight characteristics are amazing and it flys on rails. Landing her is an easy thing. If you like, add wingtip missiles or CFT´s (conformal tanks on newer Block series). Have fun and thanks to Craig for a grat design!!

  3. Barry Fleming

    Absolutely stunning flyer 🙂
    I build the Pusher version and included 3D printed nosecone, intake, exhaust, wingtip missiles and carriers. if you can id suggest clear canopy also to finish it of beautifully.
    Build was very clean, easy and quick all from 1 sheet of 6mm Depron 80x125cm
    Build guide was very helpful and there is also a build video available 🙂
    power set up
    NTM 28-36 Prop drive v1 2700kV
    6×4 APC pusher prop
    4 servos – 2 for ailerons on independent channels and 2 independent channels again on elevator for unlimited mixing through radio.
    the F-16 will run on 2 servos on the elevator set up on Tailerons no problem at all and still fly superb
    3000mAH 4s Battery
    70amp Red Brick ESC ( needed for running NTM on 4s with 6×4 prop )
    final build weight including paint hahaha and crazy pilot in the cockpit around 780g
    finisher her off with Jetworks Viper Demo paint scheme
    this can be built lighter without 3d pars and smaller power train.
    CG on the General arrangement is on the money.
    the travel i have set
    14mm +/- Aileron
    22mm +/- Elevator
    however with High alpha flying and spoilerons i have extended the throws to Crazy level +/- and high alpha she does.
    another superbly designed amazing flyer
    buy it, build it, fly it, love it
    Maiden flight
    https://www.youtube.com/watch?v=tTBqUnqxmoM
    High alpha spoileron fun
    https://www.youtube.com/watch?v=aiDKLgw80NE

Add a review

Your email address will not be published. Required fields are marked *